The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
We have stumbled on this article involving Installing A Bathtub below on the net and figured it made good sense to share it with you on my blog.
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently obtainable, the project can move easily; if you need to open a wall surface to get rid of the old tub as well as position the new bath tub, the job is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also set in the new one. Make sure you have qualified on your own for the task and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration employing one before you begin. Chances are you might need a specialist plumber to make tube links.
This short article will assist you install a new bath tub in your restroom if you have actually currently acquired a brand-new bathtub and also do not need to transform the plan of your previous water system pipes.
Your devices as well as material list should comprise the following:
Preparing for the Installment
To start with, the supporting structure supplied with the bath needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather troublesome because of the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the tub in the called for setting. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub till the level reviews degree.
To install faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression join; after that do the same for the other tap.
Turn on the water supply and check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the bath tub needs to wait up until the bath tub has been utilized a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer offered backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, triggering the water to pass through the wall surface in between the bath and also the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill the tub with water prior to securing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader about A Step-by-Step Guide to Installing a Bathtub, I think sharing that segment was a good thing. Are you aware of another person who is fascinated about the subject? Why not share it. Many thanks for your time spent reading it.
Protect your property; contact now. Report this page